Help video · Basics

First station with a second line

A second line around the oval with a crossover, smart snapping, turning the layout, a halt with platforms and a station building, hints in the check.

Length: 06:26

Show in the editor ↗

Transcript

Welcome to part 2! We’ll keep building on the oval from part 1. Today it gets a second line and a station.

Before we start, let’s ask the check, top right. It looks at your plan like an experienced modeller and gives you hints.

It has already found a station: where two tracks run side by side, it suspects one.

There’s also a hint: the siding has no uncoupling track. On a Märklin layout, that’s where you uncouple the cars. Here it sorts itself out, because the siding becomes part of the second line, and there’s no more shunting there.

With Premium, the check also looks at the running geometry, such as S-curves and gaps at the joints.

Let’s start at the siding. First, the curve at the turnout goes: a double-click selects just that track, then delete.

In its place goes a second turnout, again picked up by its points. Its branch meets the branch of the first turnout exactly.

Two turnouts, branch to branch, make a crossover. The two tracks are then 77.5 millimetres apart. You know that value from the catalog: it’s shown there as the spacing between two radii.

A short straight continues the new track to the left.

At the other end, the buffer stop is now in the way. Double-click, Delete, and it’s gone.

The old siding is too long for the second line. Grab its end and push it back until it stops where the inner curve begins. Trackplanner puts in the right straight for you.

Now for smart snapping. Drag a long straight next to the oval at the bottom, even a little too far away. Trackplanner lays it parallel, at the right track spacing.

The short straight works the same way. That’s how you get parallel tracks without measuring.

Curves work too. Drag an R2 curve next to the bend: Trackplanner takes the larger R3 radius instead and lays it at the right distance.

A tip: hold Alt while you drag, and nothing snaps. The track stays exactly where you let go. Ctrl+Z puts it back in place.

If you'd rather plan without smart snapping altogether, turn it off at the bottom right under “Display & Grid”.

A second R3 curve fills the gap to the old siding. It snaps in at both ends.

Add the remaining curves by double-clicking, as in part 1, now with R3, until they meet the straights at the bottom.

On the other side we first add two R3 curves to the straight.

Now for building on: press the end of the curve and keep dragging around the circle. Trackplanner adds curve after curve, as far as you drag. At the crossover the last curve snaps in, and the second line is closed.

Now you have two lines. Two trains can run at the same time, and the crossover lets them switch from one to the other. With Premium, by the way, the parallel track tool lays the whole second line in one go.

Where does the station go? On the straight side at the bottom, with no turnout in the way. Strictly speaking it’s a halt: trains only stop here and change tracks at the crossover.

But the building should go at the back, so it doesn’t block the view of the trains. So we turn the whole layout around. Ctrl+A selects everything.

Now drag the rotate handle and turn the layout around in one go. With the mouse we land at 165 degrees, just off.

No problem: in Trackplanner you can type in any number.

Click the angle, type 180 and press Enter. Now the halt is at the top, which means at the back.

For the scenery, let’s open the 3D view alongside. In the view menu at the top right, choose “Side by side”: you keep building in 2D, and right next to it you see the same layout in 3D.

The two views are linked: when you move or zoom the plan, the 3D view follows, and the other way round. You can switch this off at the bottom right under “Display & Grid”, with “Link cameras”.

A halt needs a platform and a station building. You’ll find both in the Scenery tool. It has everything that goes next to the tracks: trees, buildings, bridges, platforms and signal boxes, vehicles and figures. Many of them are real kits you can buy.

We search for the platform: type platform and press Enter. Now all the results show up large in the catalog, and we take the one for C track.

It goes between the two tracks and snaps into the middle by itself. This island platform fits the C track spacing exactly.

Add a platform end on the left and on the right. They snap to the track too.

For the building there’s a second way, the filters. The Railway theme shows every building around the tracks, including lots of stations.

Click the i to open the detail card. It shows dimensions, article number and price, and takes you straight to buying it.

We take Faller’s Peterstal halt and put it behind the second line. You can place buildings freely, wherever you like.

Finally, the check once more. The hint about the uncoupling track is gone, because there’s no shunting here any more.

To finish, we switch to “3D only”. The 3D view then fills the whole screen.

Hold the left mouse button to turn the layout and tilt the view up or down.

With the right mouse button you move the view, and the mouse wheel zooms in, here all the way to the station building.

This is your first station in 3D: two lines, a crossover and a halt with an island platform and a station building. Have fun building on!

The voice is generated with AI from Georg’s voice.