First oval with turnout and siding
Transcript
Let’s get started! On the left is the track catalog. It shows the track system you picked when you created the plan.
The search box at the top finds track by article number, radius or name, for example “Buffer stop”.
Use drag and drop to pull the first straight into the plan.
Drag the next straight over, a long one this time, and watch: it docks onto the open end by itself.
To move the view, drag with the right mouse button held down, or use the arrow keys.
Now let’s add the first curve. Like the straight, it snaps into place at the open end.
You flip the curve with the space bar or the “flip” button. Press again and it flips back.
To see more of the plan, zoom with the mouse wheel or use the buttons at the bottom right.
Let’s keep going with curves. Drag the next one onto the open end.
Double-clicking the tile is quicker: every double-click adds a piece to the selected track. Six curves of 30 degrees make half a circle.
A long and a short straight form the bottom side, just like at the top. The straights make it an oval instead of a circle.
Six more curves. The last one meets the first straight, and the oval snaps shut by itself.
Made it: the oval is closed, and there are no open ends left.
Before we add the turnout, a quick word on selecting. A single click always selects the whole strand up to the next turnout. There’s no turnout here yet, so that’s the entire oval.
A double-click, on the other hand, selects just that one track.
Use the “delete” button at the bottom or the Delete key to remove the straight. Now the oval has a gap.
Grab the turnout in the catalog by its toe, the end where the track hasn’t split yet, and drag it into the gap. It’s as long as the straight, snaps in at both ends, and the oval is closed again.
By the way: don’t be afraid of making mistakes. Every action can be undone, with Ctrl+Z or the “Undo” button at the top. Undo twice, and the straight is back.
But there’s an easier way, and the straight doesn’t have to fit. The long straight here is almost twice as long as the turnout. The turnout goes at its end, right where it meets the curve.
Drag the turnout from the catalog right onto this joint. When the pointer reads “inserts switch”, let go.
Trackplanner has taken out the long straight and fitted a shorter piece of the right length next to the turnout. The oval stays closed.
The space bar helps here too: it turns the left turnout into a right one and points it the other way. After four presses it’s back where it started.
The siding starts at the diverging track. To run parallel to the main track, it needs a curve that bends back by the same angle as the turnout. The catalog shows the angle: on the turnout’s tile it comes right after the article number, here 24.3 degrees.
In the catalog, the curves are grouped by radius: R1, R2 and so on. Each group shows the distance to the next smaller radius. That’s also the spacing between two parallel tracks.
Under R2 is the 24.3 degree curve that matches the turnout. Select it and click the add arrow on the diverging track. The curve bends back, and the track runs parallel to the main track.
A double-click on the straight’s tile makes the siding longer.
The quickest way to find the buffer stop is the search. Double-click its tile to put it on the end.
Click the siding, and its length shows in the bar at the bottom, here next to “Total”. For a small loco it should be at least 30 centimeters.
But your train is longer, so the siding needs to grow. That’s what the stretch handle with the double arrow at the end of the track is for. Drag it to the right: the track gets a good 30 centimeters longer, and Trackplanner puts in the right straights itself.
Now the siding sticks out past the oval on the right. That can be fixed too, with a little trick.
You can move a turnout together with everything attached to it. Click the turnout and drag its slide handle to the left. The whole siding moves with it and no longer sticks out past the oval. The oval stays closed.
And that’s your first layout finished: an oval, a turnout and a siding with a buffer stop. Have fun building from here!
The voice is generated with AI from Georg’s voice.